| Poster |
Message |
 mix112
 |
 chevy traspordi automaatne uste lukustamine
Küsimus siis selline, et kuidas selle elimineerida saab? raamatust ma seda välja ei loe kuna see saksa keelne. |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
01.02.2010 at 22:57 |
|
antennimees
 |
chevy traspordi automaatne uste lukustamine
AUTOMATIC DOOR LOCK OPERATION MODES
Mode 1
Shift out of Park lock, ignition off unlock, and shift into Park unlock modes are disabled.
Mode 2
Shift out of Park mode enabled. Ignition off unlock and shift into Park unlock modes disabled.
Mode 3
Shift out of Park and ignition off unlock modes are enabled. Shift into Park unlock mode disabled.
Mode 4
Shift out of Park lock and shift into Park unlock modes enabled. Ignition off unlock mode disabled.
CHANGING AUTOMATIC DOOR LOCK OPERATION MODE
1. Turn off instrument panel dimmer switch. Turn ignition switch to LOCK position.
2. Remove BCM PRGRM fuse located in instrument panel fuse block. Turn ignition switch to ACC
position. BCM will sound chime (2, 3 or 4 chimes) corresponding to BCM type installed on vehicle.
BCM has now entered the feature customization mode.
3. To change automatic door lock operation mode, press and release LOCK on either door lock switch.
BCM will sound chime a number of times equivalent to automatic door lock operation modes. See
AUTOMATIC DOOR LOCK OPERATION MODES . When Mode 4 is reached, Mode 1 will be
repeated. To exit and save current customization mode, turn ignition off. Replace BCM PRGRM fuse.
CHANGING LOCKING CONTROL MODES
1. Turn off instrument panel dimmer switch. Turn ignition switch to LOCK position. Remove BCM
PRGRM fuse.
2. Turn ignition switch to ACC position. BCM will sound chime (2, 3 or 4 chimes) corresponding to
BCM type installed on vehicle. BCM has now entered the feature customization mode.
3. To change locking control mode, press and release UNLOCK on either door lock switch. BCM will
sound chime equivalent to locking control mode. When Mode 4 is reached, Mode 1 will be repeated.
To exit and save current customization mode, turn ignition off and reinstall BCM PRGRM fuse. The
lock control modes are as follows:
Mode 1
Last door locking and lock-out prevention disabled.
Mode 2
Last door closed locking disabled. Lock-out prevention enabled. BCM will not lock doors when pressing
LOCK on either door lock switch and key in ignition cylinder but driver-side door is open.
Mode 3
Last door closed locking enabled. Lock-out prevention disabled. This mode locks all doors 5 seconds after
closing all doors when pressing LOCK on either door lock switch with ignition switch in LOCK position.
Mode 4
Last door closed locking enabled, will lock all doors 5 seconds after closing all doors when pressing LOCK
on either door lock switch with ignition switch in LOCK position. Lock-out prevention enabled, will not
lock doors when pressing LOCK on either door lock switch with key in ignition cylinder but driver-side
door is open.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
02.02.2010 at 19:53 |
|
antennimees
|
chevy traspordi automaatne uste lukustamine
Kuna ma ei tea mis aasta auto sul on siis panin 98 aasta oma.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
02.02.2010 at 19:54 |
|
mix112
|
chevy traspordi automaatne uste lukustamine
aasta on 2003. |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
03.02.2010 at 12:15 |
|
antennimees
|
chevy traspordi automaatne uste lukustamine
Siin siis 2003 aastale:
Programming Features
Enter Programming Mode
Perform the following steps in order to enter the programming mode:
1. The optional content theft deterrent system must be disarmed.
2. With the ignition in the OFF position, remove the BCM PRGRM fuse, close the driver door.
3. Turn the ignition to the ACC position.
4. Listen to the number of chimes. The chimes indicate the BCM type (2, 3, or 4) and therefore the
features that may be personalized.
Automatic Door Locks
Continue with the following steps in order to personalize the automatic door locks:
1. Press and release the any power door lock switch. Count the number of chimes in order to determine
the current mode.
2. Press any power door lock switch again in order to advance to the next mode. The chime will sound
the number of times equivalent to the mode.
3. Continue to press any power door lock switch until you reach the desired mode.
Content Theft Deterrent
Continue with the following steps in order to personalize the content theft deterrent:
1. Cycle the park lamps (ON then OFF). Count the number of chimes in order to determine the current
mode.
2. Cycle the park lamps again in order to advance to the next mode. The chime will sound the number of
times equivalent to the mode.
3. Continue to cycle the park lamps until you reach the desired mode.
Content Theft Deterrent Arming/Disarming
Continue with the following steps in order to personalize the content theft deterrent arming/disarming:
1. Insert a second key into any door lock cylinder.
2. Rotate the key to the UNLOCK position and hold for 1 second. Count the number of chimes in order
to determine the current mode.
3. Rotate the key again or press the Panic button on vehicles equipped with keyless entry in order to
advance to the next mode. The chime will sound the number of times equivalent to the mode.
4. Continue to rotate the key or press the Panic button until you reach the desired mode.
5. Remove the key from the door lock cylinder.
Delayed Illumination and Exit Lighting
Continue with the following steps in order to personalize the delayed illumination and the exit lighting
features:
1. Turn the courtesy lamps on by turning the instrument panel brightness control all the way to the
DOME position. Count the number of chimes in order to determine the current mode.
2. Turn the courtesy lamps to the DOME position again in order to advance to the next mode. The chime
will sound the number of times equivalent to the mode.
3. Continue to cycle the courtesy lamps until you reach the desired mode.
Delayed Locking and Lockout Prevention
Continue with the following steps in order to personalize the delayed locking and the lockout prevention
features:
1. Press the power door unlock switch. Count the number of chimes in order to determine the current
mode.
2. Press the power door unlock switch again in order to advance to the next mode. The chime will sound
the number of times equivalent to the mode.
3. Continue to press the power door unlock switch until you reach the desired mode.
Remote Activation Verification (if equipped with Keyless Entry)
Continue with the following steps in order to personalize the remote activation verification for the remote
keyless entry:
1. Press the LOCK button on the keyless entry transmitter. Count the number of chimes in order to
determine the current mode.
2. Press the LOCK button on the transmitter again in order to advance to the next mode. The chime will
sound the number of times equivalent to the mode.
3. Continue to press the LOCK button until you reach the desired mode.
Remote Unlock Control (if equipped with Keyless Entry)
Continue with the following steps in order to personalize the remote unlock control for the remote keyless
entry:
1. Press the UNLOCK button on the keyless entry transmitter. Count the number of chimes in order to
determine the current mode.
2. Press the UNLOCK button on the transmitter again in order to advance to the next mode. The chime
will sound the number of times equivalent to the mode.
3. Continue to press the UNLOCK button until you reach the desired mode.
Exit Programming
Continue with the following steps in order to exit the programming mode:
1. Turn the ignition to the OFF position.
2. Replace the BCM PRGRM fuse.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
03.02.2010 at 20:07 |
|
mix112
|
chevy traspordi automaatne uste lukustamine
tänud |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
03.02.2010 at 23:38 |
|
Kummipuru
|
chevy traspordi automaatne uste lukustamine
kas samasugune info on ka 2004 Navigatori kohta?
____________________________
puidust väikeehitised ja saunad
võitlussport, enesekaitse, eratreeningud |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
04.02.2010 at 15:57 |
|
antennimees
|
chevy traspordi automaatne uste lukustamine
Ikka on:
AUTOLOCK AND HORN CHIRP PROGRAMMING
1. Close all the doors.
2. Confirm that the ignition switch is in the OFF position.
3. Turn the ignition switch from OFF to RUN.
4. Press the power door lock UNLOCK button three times.
5. Turn the ignition switch from RUN to OFF.
6. Press the power door lock UNLOCK button three times.
7. Turn the ignition switch from OFF to RUN.
8. Verify that the horn chirps. This indicates the system is in the enable/disable mode is ready to accept
program changes.
9. Press the power door lock UNLOCK button one time to toggle the autolock/relock feature OFF.
10. Press the power door lock LOCK button once to enter the command.
11. Verify that the horn chirps one time. There should only be one chirp indicating that autolock/relock
feature has been disabled. If one chirp is heard, followed by a longer sound of the horn, the
autolock/relock feature has just been enabled. Return to Step 9.
12. Turn the ignition switch to the OFF position to exit the enable/disable mode.
13. Exit the vehicle and verify that the horn chirps once to indicate that a feature has been changed and
that autolock/relock has been disabled.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
04.02.2010 at 21:08 |
|
villem
|
chevy traspordi automaatne uste lukustamine
Äkki leiad 1999 a. chrysler 300m ja 1997 a. vojagreile ka sellise juhendi.Tänud! |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
04.02.2010 at 00:27 |
|
antennimees
|
chevy traspordi automaatne uste lukustamine
Tegelikult on need juhendid ja ka kõik teised juhendid kuidas oma autot kasutada juhtida jne. auto kasutusjuhendis kirjas. Palun lugege oma autode kasutusjuhendeid või nagu lühendatult öeldakse RTFM.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
05.02.2010 at 19:34 |
|
antennimees
|
chevy traspordi automaatne uste lukustamine
99 300M
AUTOMATIC DOOR LOCKS ENABLED/DISABLED
Close all doors. Cycle ignition switch from ON to OFF position 4 times without cranking engine. Using
power door lock switch, lock doors. If system is being disabled, a single chime should sound to indicate that
feature has been changed successfully. If chime did not sound, repeat procedure. If system is being enabled,
chime should not sound
Ja Voyager'i kohta ma kiirelt ei leia aga user manualis oli kuna enda kunagisel ma ka miskit muutsin seal.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
05.02.2010 at 19:50 |
|
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
aare45
|
chevy traspordi automaatne uste lukustamine
Kuidas ühendada alarm keskluku süsteemi, originaalpult puudub . Chevy Trans Sport 98/99.
Praegu ainult võtmega lahti.
Mingi jutu leidsin googeldades Montana kohta:
NOTE *1 the BCM (Body Control Module) is located to the RIGHT of the GLOVEBOX.
NOTE *2 if vehicle is equipped with a FACTORY KEYLESS ENTRY Module, use the RED/BLACK (-) for LOCK and the ORANGE/BLACK (-) for UNLOCK, both wires will be found at the BCM, wires will only meter with the key in the Door key cylinder. You must use the 3.5 or Long door lock pulse length output.
NOTE *3 the LIGHT BLUE/BLACK (-) operates the LEFT SLIDING DOOR, and a LIGHT BLUE (-) operates the RIGHT SLIDING DOOR.
Kas juhtimine käib miinusjuhtmega/massiga? Allajoonitud lausele ei saa pihta?
____________________________
TÖÖSTUSLIKUD VENTILAATORID
Tel:512 3835
Chrysler GV - 3,3L 2005
Hyundai IX35 4WD 2014
Citroen Berlingo 2015
----------------------------------- |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
24.11.2010 at 00:56 |
2 edits. Last edited 27.11.2010 at 16:03 by aare45
|
armasjumal
|
chevy traspordi automaatne uste lukustamine
quote:
antennimees: 99 300M
AUTOMATIC DOOR LOCKS ENABLED/DISABLED
Close all doors. Cycle ignition switch from ON to OFF position 4 times without cranking engine. Using
power door lock switch, lock doors. If system is being disabled, a single chime should sound to indicate that
feature has been changed successfully. If chime did not sound, repeat procedure. If system is being enabled,
chime should not sound
98 a concordil tõenäoliselt samamoodi. Proovin ära õhtul. Manuaali ei ole nende vanade autodega kaasas ja lihtsam on foorumist vaadata kui manual hankida
____________________________
G20 '95 |
Warning: Undefined variable $offset2 in /data01/virt688/domeenid/www.tqhq.ee/test/forum/func.php on line 306
25.11.2010 at 11:27 |
|
